广东厂房降温公司和你分析轴流风机的准备工作和安装事项

广东厂房降温公司和你分析轴流风机的准备工作和安装事项

     ，主要经营各类车间降温工程设备：包括环保空调、负压风机、离心风机、柜式风机、降温水帘、通风降温设备、车间抽风降温设备、厂房除尘设备等。

    今天厂房降温设备公司和你大家分享轴流风机的准备工作和安装事项，如下：
开箱检查风机各部件是否齐全，机壳外部有否碰伤，特别要注意头部整流器是否有碰伤变形，各部件联接是否紧密，叶片电机有无损伤，叶轮转动是否灵活，如发现问题应予以修理及调整。检查风机的安装基础，它必须有足够的强度和刚度，以保证能承受风机运行时的负荷，同时检查基础与风机的联接尺寸是否符合设计要求。
轴流风机的安装事项如下：
事项1、风机卧地式安装把减振器通过联接螺栓固定于风机机座，用中心高调整垫板调节各减振器水平高度，表示用固定螺栓把风机固于已焊接在基础上的联接钢板上，如风机由于抗震等原因无需减振器，则把风机机座上的螺孔与基础上的预埋螺栓直接联接即可。
事项2、侧墙卧式安装风机安装的基本要求与卧地式安装相同，只是安装托架做成斜臂支撑式，托架要有足够的强度和刚度，10#以上风机不宜采用此种安装方式。
事项3、悬挂式安装先把减振器与风机用螺栓联接成一体，减振器对称安装，布置于风机重心两侧，直接把提升插入安装于悬挂支架，悬挂支架的高度，视实际空间距离由用户自定，16#以上风机一般不采用此种安装型式。
事项4、立式安装风机立式安装方法与卧地式安装一致，对风机基础的强度与刚度要求更严格。
事项5、风机与两端管道的联接必须采用挠性接头，以隔离振动和保护风机。

Guangdong cooling plant company, mainly engaged in various types of cooling plant engineering equipment, including environmental protection, air conditioning, suction fan, centrifugal fan, cabinet type fan, cooling water curtain, ventilation cooling equipment, workshop ventilation cooling equipment, plant dust removal equipment etc..
Today plant cooling equipment company and you all share the work and installation of the axial flow fan, as follows:
Out of the box to check each part of the fan is complete, outside the shell is not damaged, in particular, to pay attention to whether there is a head rectifier bumps deformation, connecting all the parts is close, vane motor damage, the impeller rotation is flexible, such as the discovery of problems should be repairs and adjustments. Check the installation of the wind turbine foundation, it must have enough strength and stiffness, in order to ensure that the load can withstand the operation of the wind turbine, and check the connection size of the foundation and the fans are in accordance with the design requirements.
The installation of axial flow fan is as follows:
Notes 1, fan horizontal type installation of the shock absorber are connected through screw bolts fixed to the fan frame, plate with high adjustment to adjust the damper level height, plant cooling equipment company said lookout machine with a fixed bolt solid in welding on the basis of the connecting steel plate, wind machine due to the earthquake and other reasons without shock absorber, lookout machine screw and based on the pre buried bolt directly can be connected.
Item 2, side wall horizontal installation of the basic requirements and the installation of wind turbine is the same as the horizontal installation, but the installation bracket is made of the inclined arm support, the bracket should have enough strength and stiffness, 10# above the wind turbine is not suitable for this installation.
Item 3, hanging to install the damper and fan with bolts are connected into a whole, shock absorber symmetrically installed, arranged at the two sides of the center of gravity of the wind machine, directly on the lookout for lifting insert arranged on the hanging bracket, suspension bracket height, depending on the actual spatial distance by custom, 16# above, fan generally not by this installation type.
Item 4, vertical installation method and horizontal installation of vertical installation method, the strength and rigidity of the wind turbine foundation is more stringent.
Item 5, the connection between the fan and the two ends of the pipe must be used for flexible joints, in order to isolate vibration and protect the air blower.