[摘要]1、饲料搅拌机停机前后在物料压制即将结束时，将少许麦皮拌合食用油并投入机器内，压制1-2分钟后停机，使模具孔内充满油料，以便下次开机就能投料生产，既保养模具，又节约工时，停机后松动压轮调节螺丝，并清除残余料。
为您介绍搅拌机维护方法有哪些？
关于的问题，不是几句话就能说清的，更不是看两篇专题文章就能够掌握的。而是要通过长时间的专业实践才能弄明白、学到手的。
1、饲料搅拌机停机前后在物料压制即将结束时，将少许麦皮拌合食用油并投入机器内，压制1-2分钟后停机，使模具孔内充满油料，以便下次开机就能投料生产，既保养模具，又节约工时，停机后松动压轮调节螺丝，并清除残余料。
Feed mixer before pressing down at the end of the material, a little oatmeal to mix oil and put into the machine,pressed for 1-2 minutes after the shutdown of the die hole filled with oil, so the next boot will be able to feed production, both maintenance mold, and save hours of work, after the shutdown pressure roller adjustment screw loose, and remove residual material.
2、饲料搅拌机压轮与传动部分的维护与保养，物料中的硬杂物质或金属块应予以清除，可在机器进料口设置永磁筒、或除铁器，以免影响压轮、模具和中心轴的使用寿命。由于颗粒料在挤压过程中温度高达50-85℃，并且压轮在运转工作时承受较强的被动力，但又缺乏必要的、有效的粉尘保护装置，所以每隔2-5个工作日，必须清洗一次轴承，并加入耐高温油脂，主轴每隔一个月清洗加油一次，齿轮箱间隔半年就要进行清洗保养，传动部分的螺丝紧固更换应随时进行。
Feed mixer pressure wheel and the transmission part of care and maintenance, materials or substances in miscellaneous hard piece of metal should be removed, to set up a permanent magnet material inlet tube, or separator in the machine,so as not to affect the pressure roller, the mold and the central axis life. Since the pellets during extrusion temperatures up to 50-85 ℃, and pressure roller is subjected to a strong work force in operation, but the lack of necessary and effective dust protection device, so every 2-5 days It must be cleaned once a bearing, and add high-temperature grease, cleaning grease once a month spindle, gear box, cleaning and maintenance intervals will be carried out every six months, part of the fastening screw drive replacement should be carried out at any time.
3、饲料搅拌机模具的更换方法，压轮磨损后，可以更换压轮皮或更换成套压轮；发现轴承松动、抱死，应更换轴承或连轴一起换掉。环模颗粒机的环模老化、磨损、受伤后，松动抱箍卡盘，换上新的即可；若是螺丝固定类型，须先轻轻振动磨具，然后均匀用力卸掉螺丝，就能更换新的磨具。设别的模板一般都是反扣螺母、键槽固定，而且在模板靠内孔附近有两个对称的螺丝孔，用螺丝慢慢顶出或用拉力器、拆卸铁均匀用力拉出即可。注意在顶出或拉出过程中，要用锤子轻轻振动模板，防止螺丝断在孔内。
Replacement of feed mixer mold, wear pressure after the round, you can replace the pressure roller sets of leather or replace pressure roller; bearings found loose, lock, replace bearings or couplings replace together. Ring mold particles machine ring mold aging, wear, after the injury, loose hoop chuck and put a new can; if screw type, must first shaking gently abrasive, then even force remove screws, can be replaced the new abrasive. Flip the other templates provided are generally nuts, keyway fixed, and in the vicinity of the hole template by two symmetrical screw holes, with the top of the screw slowly or Rally, disassemble the iron even forced to pull it out. Note that at the top or pulling out the process, use a hammer to gently vibrating the template to prevent the screws off in the hole.
4、饲料搅拌机整机维护，饲料搅拌机要按说明使用配套动力。过小，产量低、效果差；过大，浪费机电、加速机械磨损、缩短使用寿命。维护保养要在断电状态下进行。机器应放在适宜工作的地方。尽可能减少搬动次数。常检修、防水浸、防雨淋、防漏电、防火、防止使用霉变饲料。
Feed mixer machine maintenance, feed mixer according to package instructions use force. Too small, low yields, poor results; too large, mechanical and electrical waste, accelerated mechanical wear, and shorten life. Maintenance to be carried out in the off state. The machine should be placed in a suitable place to work. Minimize the number of moving. Regular maintenance, water immersion, rain, leakage power, fire, prevent the use of moldy feed.
以上信息就是和新疆腻子粉搅拌机生产厂家全方位分析的相关信息，更多资讯尽在我们的官方网站。