安阳生物质锅炉出售维修厂商生物质锅炉维修安全注意事项
Anyang biomass boiler manufacturers to sell maintenance of biomass boiler maintenance safety precautions
安阳豫鑫锅炉有限公司已有三十多年锅炉和一、二、三类压力容器制造历史，主营以下系列产品：燃煤（油、气）蒸汽锅炉、生物质锅炉、热水锅炉、余热锅炉、有机热载体炉和一、二、三类压力容器，同时适应市场发展，依托先进的制造技术和科学规范的管理，注重智能和环保产品的开发，积极与大专院校、设计院联合相继开发出有机热载体余热炉、循环硫化床锅炉、纯无烟再节能旋流燃烧锅炉等节能产品。
To Anyang Yuxin Boiler Co., Ltd. has thirty years of boiler and one, two, three types of pressure vessel manufacturing history, the following main products: coal (oil and gas) steam boiler, biomass boiler, hot water boiler, waste heat boiler, organic heat carrier furnace and one, two, three types of pressure vessel while adapting to market development, relying on advanced manufacturing technology and scientific and standardized management, pay attention to the development of intelligent and environment-friendly products, actively with colleges and universities, design institutes joint have been developed organic heat carrier recovery boiler, circulating fluidized bed boiler, pure smokeless Festival can swirl combustion boilers and other energy-saving products. .
维修安全注意事项：
Maintenance safety precautions:
1、检修工作前应观察环境是否具备工作条件，不具备条件应通知值长并向上级领导汇报，停炉后方可工作。
1, maintenance work should observe whether the environment has working conditions, do not have the conditions should be notified to the long and report to the superior, stop the furnace before work.
2、检修工作前，通知运行员切断水、电、汽源并由专人挂牌。
2, maintenance work, notify the operator to cut off water, electricity, steam source and by hand.
3、检修人员佩带好劳动保护用品。
3, maintenance personnel wear good labor protection supplies.
4、登高作业须系好安全带或搭好脚手架并由一人监护。
4, climbing must fasten the safety belt or a scaffold and by a person care.
5、检修中应把工具 、各种材料、配件放置好，防止掉入设备、管道或炉膛里边。
5, maintenance should be the tool, a variety of materials, accessories placed well, to prevent falling into the equipment, pipes or furnace inside.
6、进入炉膛、烟风道等空间作业时通风条件应良好，温度降至工作温度方可进入工作。照明使用36V行灯且由一人在外监护经常与里边工作人员联系。
6, into the furnace, smoke and air ducts and other space operations should be good ventilation conditions, temperature drop to the working temperature can enter the work. Lighting using 36V lights and by a person outside the monitor often contact with the staff inside.
7、工作完毕后，检查是否工具、材料、配件齐全，防止遗留在炉膛等空间里边。
7, after the work is completed, check whether the tools, materials, accessories complete, to prevent the remnants of the space inside the furnace and so on.
8、工作完毕后，专人摘牌，验收合格后方可离开工作现场。
8, after work, someone delisting acceptance before leaving the work site.
9、将检修结果汇报值长，并做好检修记录。
9, the maintenance of the results of a long report, and do a good job of maintenance records. .