河南优质门窗厂家为您讲解门窗安装的正确方法

    河南优质门窗厂家为您讲解门窗安装的正确方法，安阳亚美门窗有限公司在建筑建材行业已立足几十余年风雨，有着举足轻重的地位。在门窗五金的研究设计上有着自己的专业的团队和成熟的研发经验。一直以新型门窗的研发和质量的严格把关为企业理念。为客户生产更安全、质量更有保证的产品。欢迎大家来我厂实地考察或来电咨询。门窗的正确安装方法：
    门窗套正确安装方式1
 检查基层材料选用合格木龙骨及15㎜细木工板或中纤板为基层材料。施工前检查基层墙体平整度误差超过30㎜采用相应措施墙体破损较大的在木作基层作好后应用水泥砂浆找补平整后方能进行面层施工。
门窗套正确安装方式2
门窗套基层细木工板套材下料基层用干燥木料打木楔固定稳固离地5㎜防止水浸。封面层板使用白乳胶、钉子固定白乳胶应涂刷均匀足量修边时严禁修伤面板。
    门窗套正确安装方式3
门扇制作厚度一般为38㎜左右装锁处特别加固木工板可做交叉开口处理以防变形。
门窗套正确安装方式4
门窗扇安装：门窗与地面(面层高度)距离5-8mm门扇左右上口间隙2-3mm门扇与门档结合严密缝隙≤2mm合页位距为立挺高度1/10。装门扇涉及磨砂玻璃时装好后应在光面部分打适量玻璃胶保护玻璃厨卫间磨砂面应向外室外交结处磨砂面应向内。
门窗套正确安装方式5
安装合页须在门扇及门框上双面开槽门扇开口与合页严密。
 门窗套正确安装方式6
门锁离地高度900-1000mm(锁中心位)锁孔位置正确锁舌与门扇锁扣与门框之间的缝隙应严密。锁安装好后必须包扎保护以防污染。
门窗套正确安装方式7
推拉门：门窗扇1500mm以内轨道使用小号滑轨;1500-2000mm使用中号;2000mm以上使用大号滑轨。确定双扇双轨推拉门门扇宽度时，两个门扇的交结边应有10mm以上重合。横竖缝应均匀、严密、暗藏式推拉门应在门扇装好且调试合格后方能封闭。
门窗套正确安装方式8
施工中应特别注意门套上口及门扇上下边的处理要求做到平整、光洁。
  Henan quality manufacturers of doors and windows for you to explain and correct installation method, Anyang Yamei doors and windows Co., Ltd. in the building materials industry has been based in more than dozens of years of wind and rain, a pivotal position. In the research and design of doors and windows hardware has its own professional team and mature R & D experience. Has been the development and quality of new doors and windows of the strict quality control for the enterprise concept. For customers to produce more secure, more guaranteed quality products. Welcome to my factory site visits or telephone consultation. Correct installation method for door and window:
Doors and windows set the correct way to install 1
Check the base material selection of qualified wood keel and 15 mm joinery board or MDF as base material. Before the construction of check the wall of the base level error more than 30 mm with corresponding measures wall damage larger in wood base prepared with cement mortar Zhaobu flat rear can surface layer construction.
Doors and windows set the correct way to install 2
A basic Blockboard next set of wood materials with dry wood base hit wedge fixed solid ground 5 mm to prevent flooding. The cover plate with white latex, nail white latex should be painted in uniform enough trimming non injury repair panel.
Doors and windows set the correct way to install 3
The door leaf thickness of 38 mm or so making a lock at the special reinforced wood board do cross opening treatment to prevent deformation.
Doors and windows set the correct way to install 4
Door and window installation: doors and windows and the ground (surface level) about distance 5-8mm door catchy gap 2-3mm door and gate file binding tight gap is less than or equal to 2mm hinge spacing is upright height of 1 / 10. Install door relates to the fashion of frosted glass should be in the smooth part of the play proper glass protective glue glass kitchen matte surface should be outward room diplomatic knot matte surface facing inwards.
Doors and windows set the correct way to install 5
The installation must be in doors and door hinge door opening and hinges tight side grooved.
Doors and windows set the correct way to install 6
Door height 900-1000mm (lock center position) the correct position of the lock keyhole gap between the tongue and the door lock and door frame should be tight. After the lock is installed, the protection must be wrapped to prevent contamination.
Doors and windows set the correct way to install 7
Sliding doors and windows fan: within the 1500mm orbit using small slide; 1500-2000mm medium; more than 2000mm using a large slide. Determine the double fan dual sliding door leaf width, two leaf edge should be 10mm above coincide with. Anyway, seams should be uniform and tight, hidden in the door sliding door should be installed and commissioning qualified rear can be closed.
Doors and windows set the correct way to install 8
Special attention should be paid to treatment under the door catchy and the door panel requires smooth and clean construction.